Form - Site Report - Planiform

Company

This field is for validation purposes and should be left unchanged.

This form must be sent by the installer when he is on site.

Employee name (Leader)*

Order number*

Client*

City*

Work performed*

Service Call

Is it a service call*

Yes
No

Is this a Metalproguetti system?*

Yes
No

Ensure completion of inspection report*

Yes
No

If no, why:

Ensure system rigidity (add bracing if necessary)*

Yes
No
N/A

Affected nuts and bolts are tightened and in good condition*

Yes
No (if not, change them)

Affected bolts and nuts are marked with Sharpie*

Yes
No

The equipment used has been accounted for (clamps, PCB, UBolt, tube, etc.).*

Yes
No
N/A

The system has been tested (see if everything works)*

Yes
No

If no, why:

Assembly

Suspension*

Yes
No

TRUFAs are securely fastened and cannot be moved*

Yes
No
N/A

Clamp bolts in good condition*

Yes
No

Clamps are locked with 2 Tek*

Yes
No

Bolts and nuts are marked with Sharpie*

Yes
No

Threads for each threaded rod are punched (prevents nuts from unscrewing)*

Yes
No
N/A

Rigid suspension (add bracing if necessary)*

Yes
No

Mezzanine Structure*

Yes
No

Excess anchor lengths are cut and rounded off*

Yes
No

Anchors are tightened to the torque specified on the drawing (torque the anchors).*

Yes
No

Anchors, washers, nuts and baseplate are marked in pencil*

Yes
No

Bolts and nuts are Sharpie-marked (tightened)*

Yes
No

Rigid structure (bracing)*

Yes
No

The structure is level (Shimmer if required)*

Yes
No

Mini-Structure*

Yes
No

Legs have Tapcons/Ancorrages (2 per flange)*

Yes
No

The mini-structure is rigid (bracing)*

Yes
No

The joints of the mini-structure have 2 Teks on each side by marking them with a Sharpie*

Yes
No

Clamp bolts in good condition*

Yes
No

Clamps are locked with 2 Tek*

Yes
No

Make sure each leg base is locked with 2 Teks*

Yes
No

Static Rack*

Yes
No

Legs have Tapcons/Ancorrages (2 per flange)*

Yes
No

Static Rack is rigid (bracing)*

Yes
No

Make sure each leg base is locked with 2 Teks*

Yes
No

Clamp bolts in good condition*

Yes
No

Clamps are crossed out with 2 Teks*

Yes
No

Arms are tightened and locked with 1 Tek*

Yes
No

Smooth joints*

Yes
No

Rail joints have 2 Teks on each side from below*

Yes
No

Rails have their Teks on their Arms from below*

Yes
No

Rails have rubber end caps*

Yes
No
N/A

Rail and V-Rail*

Yes
No

Rigid suspension (add bracing if necessary)*

Yes
No

Clamps are locked with 2 Teks*

Yes
No

Clamp bolts in good condition*

Yes
No

Bolts and nuts are marked with Sharpie*

Yes
No

Check that all joints are smooth*

Yes
No

Ensure correct operation of each switch (90, Delta, switch 45, Curve 90, etc.).*

Yes
No

Test the rails with a loaded trolley*

Yes
No

Booster*

Yes
No

Rigid suspension (add bracing if necessary)*

Yes
No

Pipe clamp bolts in good condition*

Yes
No

Clamps are locked with 2 Teks*

Yes
No

Bolts and nuts are marked with Sharpie*

Yes
No

Check that the gearbox breather is installed and that the gearbox cap is removed.*

Yes
No

The conveyor is well greased and free of burrs*

Yes
No

Validate that the conveyor speed matches that of the drawing*

Yes
No

The conveyor was tested with and without trolleys in both directions (trolleys must be loaded)*

Yes
No

If no, why:

Make sure there's Planiform sticker on the booster guard*

Yes
No

Conveyor

NPF*

Yes
No

Joints are well grinded (yokes don't jump)*

Yes
No

Bolts and nuts marked with Sharpie (they have been tightened)*

Yes
No

Set Screws on leg sleeves are tightened AND secured with big Teks*

Yes
No

The Pin holds the Yoke at its Lockpin and faces away from the conveyor*

Yes
No

Engine brake engaged*

Yes
No
N/A

Confirm speed to 85 ft/min*

Yes
No

The conveyor is equipped with an electronic selector*

Yes
No

Reflector secured with screws*

Yes
No

Test procedure successfully completed*

Yes
No

1. Call plate #10 2. Call plate #20 3. Call up the last plate on the conveyor. 4. Call up the last wafer on the conveyor minus 10 (e.g. if 50 total wafers, then 50-10=#40). 5. Call up wafer #10 again

If no, why:

Conveyor with any type of attachment (basket, hook, etc.)*

Yes
No

Check that they are properly assembled*

Yes
No

Cable trays are securely fastened*

Yes
No

Electrical cables are securely fastened to the cable tray (no dangling cables)*

Yes
No

All sensors are functional*

Yes
No

Make sure there's Planiform sticker on the electrical panel*

Yes
No

Be sure to visibly apply Planiform 1''x3'' gray decals to engine and idler sections*

Yes
No

The conveyor has been tested*

Yes
No

If no, why:

Spiked Conveyor*

Yes
No

Rigid suspension (add Bracing if necessary)*

Yes
No

Clams are locked with 2 Teks*

Yes
No

Clam bolts in good condition*

Yes
No

Clamps on the conveyor are locked with 1 Tek*

Yes
No

Bolts and nuts are marked with Sharpie (They have been tightened)*

Yes
No

Check that the Gearbox Breather is installed and that the cap is removed*

Yes
No

Validate that the conveyor speed matches that of the drawing*

Yes
No

Conveyor is well greased and free of burrs*

Yes
No

Check for Planiform stickers on the engine section guard*

Yes
No

Check that Planiform stickers are affixed to the electrical panel*

Yes
No

The conveyor has been tested*

Yes
No

If no, why:

Conveyor turns in one direction only*

Yes
No

Respect the direction of rotation of the blueprint*

Yes
No

The tensioner is fitted with springs*

Yes
No

The conveyor runs in both directions*

Yes
No

The tensioner must not have a spring (if it does, check with the engineer).*

Yes
No

A2B*

Yes
No

Rigid suspension (add Bracing if necessary)*

Yes
No

Clams are locked with 2 Teks*

Yes
No

Clamp bolts in good condition*

Yes
No

Bolts and nuts marked with Sharpie (They have been tightened)*

Yes
No

Check that the Gearbox Breather is installed and the cap removed*

Yes
No

Validate that the conveyor speed matches that of the blueprint*

Yes
No

The conveyor is well greased and free of burrs*

Yes
No

Clip strips are installed and secured with spring pins*

Yes
No

The clips and/or pins are in good condition and well oriented*

Yes
No

Check that no clips lift in curves (no hooking in strip clips)*

Yes
No

Check tension on tensioner (between 1 1/2'' and 2'' opening)*

Yes
No

Cable trays are securely fastened*

Yes
No

Electrical cables are securely fastened to the cable tray (no dangling cables)*

Yes
No

The sensors are all functional*

Yes
No

Air ducts securely fastened to cable trays (no dangling ducts)*

Yes
No

Make sure there are no air leaks*

Yes
No

Check that the air inlet is at the correct pressure (according to the required pressure gauge)*

Yes
No

Check that each drop is functional*

Yes
No

Cut all Tie-Wrap*

Yes
No

Check for Planiform stickers on the engine section guard*

Yes
No

Make sure the Planiform sticker is affixed to the electrical panel*

Yes
No

Check that the inspection report has been completed (External inspection report)*

Yes
No

The conveyor has been tested*

Yes
No

If no, why:

General system revision

Paint touch-ups are done*

Yes
No

Make sure the system is clean (no grease or other stains)*

Yes
No

Ensure that part identification is removed (taps, markers, etc.)*

Yes
No

Make sure you've removed any unnecessary Tie-Wrap and cut off any excess from used ones*

Yes
No

Cleaning up the site*

Yes
No

Return material*

Yes
No

Validate with the project manager the material to be returned*

Yes
No

Send pallet contents to be returned to project manager (list + photo)*

Yes
No

Have placed the return material on the pallet (NO PARTYMIX)*

Yes
No

Have packed and clearly identified the pallet for the return of materials*

Yes
No

Ensure that the return material is located in a place chosen by the customer.*

Yes
No
N/A

Client

Notify the customer when the job is finished*

Yes
No

Tour the installation with the customer to ensure satisfaction*

Yes
No

Have the customer sign the invoice (Blue Bill)*

Yes
No

Make sure you have the cheque in hand before you leave if the job is COD*

Yes
No
N/A

Attach a file * Please attach a minimum of 3 photos and a video of the system*

Max. file size: 64 MB.

Attach a file 2

Max. file size: 64 MB.

Attach a file 3

Max. file size: 64 MB.

Attach a file 4

Max. file size: 64 MB.

Comments

Confirmation*

The installation team must wait for the approval of the installer manager before leaving the site.